Kia key pin code

Links

Expert tip #4: Meet the experts at http://community.wikidot.com!

SMARTRA introduction

The SMARTRA stands for SMARt TRansponder Antenna. The SMARTRA unit contains an integrated inductive antenna and electronics around the ignition lock assembly.

The SMARTRA does not carry out the check of validity of transponder or the calculation of encryption algorithm. This device is only an advanced interface, which converts the RF data flow (radio frequency of 125 kHz) of transponder into serial communication to ECM and vice versa. The SMARTRA communicates to a engine control module via a dedicated communications line (called W-Line, or Immo-Line). During communication of ECM and SMARTRA the K line of ECM cannot be used for communication. The ECM controls the communication either to SMARTRA or diagnostic equipment on K line by switching of a multiplexer and specific communication procedures. The multiplexer is a part of ECM hardware.
The immobilizer system consists of the ECM, the SMARTRA, the lamp and ignition keys with built-in transponder. The ECM carries out the check of ignition key by special encryption algorithm, which runs in the transponder and in the ECM in parallel. Only if the results are equal the engine can be started. The data of all transponder, which are valid for the vehicle, are stored in the ECM.
During the key teaching procedure the transponder will be programmed with vehicle specific data. The vehicle specific data are written into the transponder memory.

PIN codes

PIN code stands for of Product Identification Number code. The PIN code is a unique code for each vehicle and it is programmed into ECM at production line.

PIN code is needed when the teaching new ECM and new keys, e.g.

1. When a new key is added
2. When replacing with new ECM or used ECM (neutralized ECM)
3. When a key is lost and needs to be deleted

If you enter incorrect pin 3 times the immobilizer (SMARTRA or Smart key) will lock In order to unlock:

• For mechanical keys leave key on for 1 hour.
• For smart key (proximity) leave car alone with good battery charge for 1 hour.

Vehicle PIN code can be obtained through www.PATSCode.com service or through Hyundai dealer.

Supported vehicles

Following list shows all vehicles for which is key teaching supported:

Manufecture	Model	Production	Manufacture	Model	Production
Dodge	Atos	2000-2004	Hyundai	i10	2008-2011
Hyundai	Accent	2000-2011	Hyundai	i20	2009-2011
Hyundai	Amica	2000-2004	Hyundai	i30	2008-2011
Hyundai	Atos Prime	2000-2004	Hyundai	i40	2012
Hyundai	Atos	2002-2009	Hyundai	i45	2011
Hyundai	Atoz	2000-2004	Hyundai	i800	2002-2009
Hyundai	Azera	2006-2012	Hyundai	ix20	2011
Hyundai	Centennial	2010-2012	Hyundai	ix35	2010-2011
Hyundai	Elantra Neos	2008-2011	Hyundai	ix55	2007-2011
Hyundai	Elantra	2001-2012	Inokom	Atos	2000-2004
Hyundai	Equus	2010-2012	Kia	Borrego	2009-2010
Hyundai	Genesis Coupe	2009-2011	KIa	Cadenza	2010-2011
Hyundai	Genesis	2009-2012	Kia	Carens	2003-2010
Hyundai	Getz	2003-2011	Kia	Carnival	2002-2011
Hyundai	Granduer	2006-2012	Kia	Ceed	2006-2010
Hyundai	H-1 Bus	2008-2011	Kia	Cerato	2003-2010
Hyundai	H-1	2002-2009	Kia	Forte	2009-2010
Hyundai	H-200	2002-2009	Kia	K2500	2005-2010
Hyundai	HD Coupe	2002-2008	Kia	K2700	2005-2010
Hyundai	Liberto	2002-2009	Kia	K3000	2005-2010
Hyundai	Matrix	2002-2011	Kia	K3000S	2005-2010
Hyundai	Santafe	2001-2011	Kia	Magentis	2006-2010
Hyundai	Santro Xing	2000-2004	Kia	Mohave	2004-2010
Hyundai	Santro	2000-2004	Kia	Opirus	2004-2010
Hyundai	Satellite	2002-2009	Kia	Optima	2006-2010
Hyundai	Solaris	2011	Kia	Picanto	2003-2010
Hyundai	Sonata	2005-2011	Kia	Pregio	2006
Hyundai	Starex	2002-2009	Kia	Rio	2005-2010
Hyundai	Terracan	2001-2006	Kia	Sedona	2002-2011
Hyundai	Tiburon	2002-2008	Kia	Shuma	2001-2004
Hyundai	Trajet XG	2000-2007	Kia	Sorento	2002-2010
Hyundai	Tucson	2005-2011	Kia	Soul	2009-2010
Hyundai	Tuscani	2002-2008	Kia	Spectra	2001-2004
Hyundai	Veloster	2011	Kia	Sportage	2005-2010
Hyundai	Veracruz	2007-2011	Kia	Venga	2010
Hyundai	Verna	2012	Kia	Visto	2000-2004

Coverage in HiCOM

Mechanical keys with RFID chip (non-proximity)

Key coding procedure is available in control unit IMMO – Immobilizer from “ECU Programming/Coding” menu.

Teaching

Engine must be turned off. Key is turned to ON position.

You will be prompted to enter a 6-digit PIN code. (eg 123456, see page 2 — PIN codes)

Now you have the key in ignition in the ON position. This key is coded after clicking on «Yes» button.

You will be prompted whether you want to code another key. If you click «yes», HiCOM will ask you to insert the next key. Up to 4 keys can be coded.(some control units allow units up to 8 keys). If you click on «No», the coding process is terminated and no more keys are added.

After successful completion of the operation, switch off the ignition for 10 seconds.

Smart key (Proximity remote)

Some vehicles have contact-less (RFID) smart-key instead of mechanical key. On these vehicles coding via SMARTRA operation will fail, it is necessary to use special dedicated smart-key control unit for this purpose. The feature can be found in Smart Key Code Saving control unit (PIC, SMKCODE).

Used smart keys cannot be programmed to another car. Please make sure you are purchasing smart keys from a trusted source.

When no valid smart key is present it is not possible to start engine and also it might be not possible to diagnose other ECUs than PIC/SMK.

Teaching

Engine must be turned off, start/stop pushbutton in OFF state.

Select «Key Teaching» feature in «ECU Programming/Coding» menu.

You will be prompted to enter a 6-digit PIN code. (eg 123456, see page 2 — PIN codes)

If you enter incorrect pin code, the ECU will lock after 2 or 3 attempts.

After this step MSL teaching starts automatically on some ECUs.

Key fob must be inserted into the Smart key holder (if there is no smart key holder, use tip of the remote to push start/stop button)

Hold Stop Start Button for 5 seconds with key in smart key holder. If your car does not have smart key holder, please use tip of the remote to push start/stop button.

The same operation will be performed for other of smart key fobs. Maximum of 2 Smart keys can be recoded.

After coding operation is complete, HiCOM displays information about successful coding.

Key information

Shows basic info about keys. Possible values: Not checked, Learnt, Virgin, Neutral, Locked

Login

This feature is used to test of PIN correctness.

Password Teaching/Changing

The password is used to switch the car into Limp mode.

You will be prompted to enter password, if the control unit is not a «Virgin». The password is numeric, consisting of 4 decimal digits (eg 1234). Regarding the Virgin control unit, you are directly prompted to set a password.

Now enter a new password. The password must consist of four-digit decimal number (eg 1234). After pressing the «Continue» button the password is set in the control unit.

Neutral mode

This function serves to use already used ECU in another vehicle.
Engine must be turned off. Key is turned to ON position.

Limp Home Mode

This function switches the car into emergency mode that is used to drive the car to workshop in case of all keys are lost or SMARTRA module is not working properly.

The ECM informs the driver about the limp home condition by 5 times blinking for 5 second. Then the user password can be sent to the ECM by HiCOM. The limp home can be activated also by the ignition key. The ECM informs the driver by blinking immobilizer lamp about the limp home condition. Then the input of user password to ECM can be done by special sequence of ignition on/off.

• Password must be set up first (using «Teaching Password/Changing» feature)
• Engine must be turned off. Key is turned to ON position.
• Type four-digit decimal number (password), eg 1234.

Источник

VIN to PIN CODE + KEY CODE for Hyundai,KIA,Renault,Peugeot,Citroen,(пин код+код ключа по вину )

Вы можете опубликовать сообщение сейчас, а зарегистрироваться позже. Если у вас есть аккаунт, войдите в него для написания от своего имени.

Сейчас на странице 0 пользователей

Лучшие авторы в этой теме

• cezar 94 публикации
• beso 18 публикаций
• s.v. 6 публикаций
• Shum80 4 публикации

Популярные дни

Популярные сообщения

cezar

VIN to PIN CODE + KEY CODE (пин код+код ключа по вину ) . Пн-Вс с 9.00-22.00 мск. ПО Hyundai,KIA: 1. Оплата 500—700 р. авто до 16г, 16-19г — 1400р для пользователей iprog, оста

pirat62

Keymaster он же буратино. ищет золотые , но никому нах не нужен. умничает , пыхтит. читать его папа Карло так и не научил.

Источник

Lonsdor K518 Read Hyundai/Kia ID46 Smart Key PIN Code by OBD

Lonsdor K518ISE key programmer is the first tool to read Kia / Hyundai PIN code for Type 46 & 47 keys by OBD and add Smart Key without PIN code. Here’s the guide on read pin code for common 46 chip and smart key 46 chip respectively.

Hyundai Mechanical key with common 46 chip

Some tools will read/decode PIN code from Hyundai/Kia common 46 chip, i.e JMD Handy Baby, ND900, VVDI2, so does Lonsdor K518

1) Read ID46 chip pin code with K518

Connect K518 host with vehicle via OBD diagnostic socket
Select Immobilizer->Hyundai/Kia->By System->Read Pin Code->Read PIN Code (46 chip)

Wait a few seconds to read PIN

2)
AD900/ND900/Handy baby/VVDI2 decode original key pin code

For Hyundai/Kia manufactured in China
P1 line: 22 29 39 is the correct PIN code

For Hyundai/Kia abroad
P2: Line 73 85 + P1 line: 78, the correct PIN code is 73 85 78.

Hyundai Smart key card with 46 chip

You need to collect key data and decode with ND900 Mini/CN900 Mini first

You properly need to try many times to collect data on Hyundai models with card slot until decode success

It is easy to collect key data on start-stop models
Attached smart key and ND900 to Start button

Remove the battery of the smart key

Decode success:
Write down the pin: ED F0 F8 EB 51 92

Select Immobilizer->Hyundai/Kia->By System->Read Pin Code->Read PIN Code (smart key 46 chip)

Remove the card slot holder
Insert a working key into the card slot

K518 require to enter 12 digit key pin decoded by mini ND900 and confirm

Displays current key ID
Reading pin code, wait for 30 sec

K518 successfully read 6-digit Pin code from Hyundai 46 smart key.

Related posts:

Источник

Read Kia Ceed 2011 Pin Code and Program Key with Lonsdor K518ISE

Here’s the guide to duplicate a key for the Kia Ceed 2011 with chip PCF7936, pin code calculation and key programming is performed by Lonsdor K518ISE key programmer.

Step 1: Calculate Pin Code

Connect K518 host wit vehicle via OBD socket

Select Immobilizer->Kia->Read Pin Code->46 Chip

Turn ignition to ON position

Read pin code in progress

Read Pin code success. The Pin is exactly the same as read by Xhorse VVDI Key Tool.

Step 2: Program chip key

Choose Select from type->Immobilizer->Type 1(CAN)

Select Program key function

Lonsdor K518 will require to enter Pin code to access

Program key success. Press Yes to program next key

Place next key and turn on ignition

Follow same procedure to program next key until program complete

The new key can start car.

Step 3: Program remote control

Select Kia->Select from type->Remote System->16 PIN->Type 4->Program remote

Note: If you are not sure about the system type, try one-by-one until success.

Don’t insert key into ignition

Program remote control: program LOCK or UNLOCK button for more than 1 s

Remote programming success.

Disconnect Lonsdor K518ISE.

Lonsdor K518ISE Read Kia Ceed 2011 Pin Code and Program Key

Источник

VIN to PIN CODE + KEY CODE for Hyundai,KIA,Renault,Peugeot,Citroen,(пин код+код ключа по вину )

Вы можете опубликовать сообщение сейчас, а зарегистрироваться позже. Если у вас есть аккаунт, войдите в него для написания от своего имени.

Сейчас на странице 0 пользователей

Лучшие авторы в этой теме

• cezar 94 публикации
• beso 18 публикаций
• s.v. 6 публикаций
• Shum80 4 публикации

Популярные дни

Популярные сообщения

cezar

VIN to PIN CODE + KEY CODE (пин код+код ключа по вину ) . Пн-Вс с 9.00-22.00 мск. ПО Hyundai,KIA: 1. Оплата 500—700 р. авто до 16г, 16-19г — 1400р для пользователей iprog, оста

pirat62

Keymaster он же буратино. ищет золотые , но никому нах не нужен. умничает , пыхтит. читать его папа Карло так и не научил.

Источник